The endurance and energy efficiency of drones remain critical challenges in their design and operation. To extend mission duration, numerous studies explored perching mechanisms that enable drones to conserve energy by temporarily suspending flight. This paper presents a new perching drone that utilizes an active flexible perching mechanism inspired by the rapid predation mechanism of the Venus flytrap, achieving perching in less than 100 ms. The proposed system is designed for high-speed adaptability to the perching targets. The overall drone design is outlined, followed by the development and validation of the biomimetic perching structure. To enhance the system stability, a cascade extended high-gain observer (EHGO) based control method is developed, which can estimate and compensate for the external disturbance in real time. The experimental results demonstrate the adaptability of the perching structure and the superiority of the cascaded EHGO in resisting wind and perching disturbances.

Human-like embodied tactile perception is crucial for the next-generation intelligent robotics. Achieving large-area, full-body soft coverage with high sensitivity and rapid response, akin to human skin, remains a formidable challenge due to critical bottlenecks in encoding efficiency and wiring complexity in existing flexible tactile sensors, thus significantly hinder the scalability and real-time performance required for human skin-level tactile perception. Herein, we present a new architecture employing code division multiple access-inspired orthogonal digital encoding to overcome these challenges. Our decentralized encoding strategy transforms conventional serial signal transmission by enabling parallel superposition of energy-orthogonal base codes from distributed sensing nodes, drastically reducing wiring requirements and increasing data throughput. We implemented and validated this strategy with off-the-shelf 16-node sensing array to reconstruct the pressure distribution, achieving a temporal resolution of 12.8 ms using only a single transmission wire. Crucially, the architecture can maintain sub-20ms latency across orders-of-magnitude variations in node number (to thousands of nodes). By fundamentally redefining signal encoding paradigms in soft electronics, this work opens new frontiers in developing scalable embodied intelligent systems with human-like sensory capabilities.

Reinforcement learning (RL) algorithms can enable high-maneuverability in unmanned aerial vehicles (MAVs), but transferring them from simulation to real-world use is challenging. Variable-pitch propeller (VPP) MAVs offer greater agility, yet their complex dynamics complicate the sim-to-real transfer. This paper introduces a novel RL framework to overcome these challenges, enabling VPP MAVs to perform advanced aerial maneuvers in real-world settings. Our approach includes real-to-sim transfer techniques-such as system identification, domain randomization, and curriculum learning to create robust training simulations and a sim-to-real transfer strategy combining a cascade control system with a fast-response low-level controller for reliable deployment. Results demonstrate the effectiveness of this framework in achieving zero-shot deployment, enabling MAVs to perform complex maneuvers such as flips and wall-backtracking.

Soft crawling robots exhibit efficient locomotion across various terrains and demonstrate robustness to diverse environmental conditions. Here, we propose a valveless soft-legged robot that integrates a pair of rotary bellows-enclosed soft transmission systems (R-BESTS). The proposed R-BESTS can directly transmit the servo rotation into leg swing motion. A timing belt controls the pair of R-BESTS to maintain synchronous rotation in opposite phases, realizing alternating tripod gaits of walking and turning. We explored several designs to understand the role of a reinforcement skeleton in twisting the R-BESTS' input bellows units. The bending sequences of the robot legs are controlled through structural design for the output bellows units. Finally, we demonstrate untethered locomotion with the soft robotic decapod. Experimental results show that our robot can walk at 1.75 centimeters per second (0.07 body length per second) for 90 min, turn with a 15-centimeter (0.6 BL) radius, carry a payload of 200 g, and adapt to different terrains.

A groundbreaking development has come from researchers at the University of Tokyo and Waseda University in Japan. They've created a biohybrid hand, a fusion of lab-grown muscle tissue and mechanical engineering, capable of gripping and making gestures. This innovation paves the way for a new generation of robotics with diverse applications. Get security alerts & expert tech tips – sign up for Kurt's The CyberGuy Report now. While soft robots and advanced prosthetics are becoming increasingly common, the combination of living tissue and machines is still relatively rare.

The approach combines the natural coordination patterns of our fingers with the decoding of motoneuron activity in the spinal column. Recent advancements in technology have revolutionized the world of assistive and medical tools, and prosthetic limbs are no exception. We've come a long way from the rigid, purely cosmetic prosthetics of the past. Today, we're seeing the rise of softer, more realistic designs, many incorporating robotic components that significantly expand their functionality. Despite these exciting developments, a major challenge remains: How do we make these robotic limbs easier and more intuitive for users to control?

Loco-manipulation calls for effective whole-body control and contact-rich interactions with the object and the environment. Existing learning-based control frameworks rely on task-specific engineered rewards, training a set of low-level skill policies and explicitly switching between them with a high-level policy or FSM, leading to quasi-static and fragile transitions between skills. In contrast, for solving highly dynamic tasks such as soccer, the robot should run towards the ball, decelerating into an optimal approach configuration to seamlessly switch to dribbling and eventually score a goal - a continuum of smooth motion. To this end, we propose to learn a single Oracle Guided Multi-mode Policy (OGMP) for mastering all the required modes and transition maneuvers to solve uni-object bipedal loco-manipulation tasks. Specifically, we design a multi-mode oracle as a closed loop state-reference generator, viewing it as a hybrid automaton with continuous reference generating dynamics and discrete mode jumps. Given such an oracle, we then train an OGMP through bounded exploration around the generated reference. Furthermore, to enforce the policy to learn the desired sequence of mode transitions, we present a novel task-agnostic mode-switching preference reward that enhances performance. The proposed approach results in successful dynamic loco-manipulation in omnidirectional soccer and box-moving tasks with a 16-DoF bipedal robot HECTOR. Supplementary video results are available at https://www.youtube.com/watch?v=gfDaRqobheg

Quadruped robots are proliferating in industrial environments where they carry sensor suites and serve as autonomous inspection platforms. Despite the advantages of legged robots over their wheeled counterparts on rough and uneven terrain, they are still yet to be able to reliably negotiate ubiquitous features of industrial infrastructure: ladders. Inability to traverse ladders prevents quadrupeds from inspecting dangerous locations, puts humans in harm's way, and reduces industrial site productivity. In this paper, we learn quadrupedal ladder climbing via a reinforcement learning-based control policy and a complementary hooked end-effector. We evaluate the robustness in simulation across different ladder inclinations, rung geometries, and inter-rung spacings. On hardware, we demonstrate zero-shot transfer with an overall 90% success rate at ladder angles ranging from 70{\deg} to 90{\deg}, consistent climbing performance during unmodeled perturbations, and climbing speeds 232x faster than the state of the art. This work expands the scope of industrial quadruped robot applications beyond inspection on nominal terrains to challenging infrastructural features in the environment, highlighting synergies between robot morphology and control policy when performing complex skills. More information can be found at the project website: https://sites.google.com/leggedrobotics.com/climbingladders.

This paper presents a low-cost, centralized modular underwater robot platform, ModCube, which can be used to study swarm coordination for a wide range of tasks in underwater environments. A ModCube structure consists of multiple ModCube robots. Each robot can move in six DoF with eight thrusters and can be rigidly connected to other ModCube robots with an electromagnet controlled by onboard computer. In this paper, we present a novel method for characterizing and visualizing dynamic behavior, along with four benchmarks to evaluate the morphological performance of the robot. Analysis shows that our ModCube design is desirable for omnidirectional tasks, compared with the configurations widely used by commercial underwater robots. We run real robot experiments in two water tanks to demonstrate the robust control and self-assemble of the proposed system, We also open-source the design and code to facilitate future research.

Future operating theatres will be equipped with robots to perform various surgical tasks including, for example, endoscope control. Human-in-the-loop supervisory control architectures where the surgeon selects from several autonomous sequences is already being successfully applied in preclinical tests. Inserting an endoscope into a trocar or introducer is a key step for every keyhole surgical procedure -- hereafter we will only refer to this device as a "trocar". Our goal is to develop a controller for autonomous trocar docking. Autonomous trocar docking is a version of the peg-in-hole problem. Extensive work in the robotics literature addresses this problem. The peg-in-hole problem has been widely studied in the context of assembly where, typically, the hole is considered static and rigid to interaction. In our case, however, the trocar is not fixed and responds to interaction. We consider a variety of surgical procedures where surgeons will utilize contact between the endoscope and trocar in order to complete the insertion successfully. To the best of our knowledge, we have not found literature that explores this particular generalization of the problem directly. Our primary contribution in this work is an optimal control formulation for automated trocar docking. We use a nonlinear optimization program to model the task, minimizing a cost function subject to constraints to find optimal joint configurations. The controller incorporates a geometric model for insertion and a force-feedback (FF) term to ensure patient safety by preventing excessive interaction forces with the trocar. Experiments, demonstrated on a real hardware lab setup, validate the approach. Our method successfully achieves trocar insertion on our real robot lab setup, and simulation trials demonstrate its ability to reduce interaction forces.